- Flexvpn Anyconnect Windows
- Anyconnect Flexvpn Over Ipv4+ipv6
- Flexvpn Anyconnect Free
- Flexvpn Anyconnect Software
Jan 04, 2020 Anyconnect SSLVPN. Cisco SSL AnyConnect VPN is a real trend these days – it allows remote users to access enterprise networks from anywhere on the Internet through an SSL VPN gateway using a web browser. During the establishment of the SSL VPN with the gateway, the client downloads and installs the AnyConnect VPN client from VPN gateway. Jun 03, 2018 FlexVPN Remote Access VPN In addition to Site-to-Site VPNs, FlexVPN can also be used for Remote Access VPN. It uses the same familiar commands as used to configure the S2S VPNs. Remote Access VPN can use certificate authentication (mutual certificate authentication between router and AnyConnect client), EAP (MD5/MSCHAPv2) and AnyConnect EAP.
Contents
Introduction
This document describes how to configure Cisco AnyConnect Secure Mobility Client to use Remote Authentication Dial-In User Service (RADIUS) and local authorization attributes in order to authenticate against Microsoft Active Directory.
Note: Currently, use of the local user database for authentication does not function on Cisco IOS® devices. This is because Cisco IOS does not function as an EAP authenticator. Enhancement request CSCui07025 has been filed to add support.
Prerequisites
Requirements
There are no specific requirements for this document.
Components Used
The information in this document is based on these software and hardware versions:
- Cisco IOS version 15.2(T) or later
- Cisco AnyConnect Secure Mobility Client version 3.0 or later
- Microsoft Active Directory
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
Conventions
Refer to the Cisco Technical Tips Conventions for more information on document conventions.
Configure
In this section, you are presented with the information in order to configure the features described in this document.
Use the Command Lookup Tool (registered customers only) in order to obtain more information on the commands used in this section.
Network Diagram
This document uses this network setup:
Configurations
This document uses these configurations:
Hub Configuration
- Configure RADIUS for authentication only and define local authorization.
The aaa authentication login list command refers to the authentication, authorization, and accounting (AAA) group (which defines the RADIUS server). The aaa authorization network list command states that locally defined users/groups are to be used. The configuration on the RADIUS server must be changed to allow authentication requests from this device. - Configure the local authorization policy.
The ip local pool command is used to define the IP addresses that are assigned to the client. An authorization policy is defined with a username of FlexVPN-Local-Policy-1, and attributes for the client (DNS servers, netmask, split list, domain name, and so forth) are configured here. - Ensure the server uses a certificate (rsa-sig) in order to authenticate itself.
Cisco AnyConnect Secure Mobility Client requires that the server authenticate itself using a certificate (rsa-sig). The router must have a web server certificate (that is, a certificate with 'server authentication' within the extended key usage extension) from a trusted certificate authority (CA).
Refer to steps 1 through 4 in ASA 8.x Manually Install 3rd Party Vendor Certificates for use with WebVPN Configuration Example, and change all instances of crypto ca to crypto pki. - Configure settings for this connection.
The crypto ikev2 profilec ontains most of the relevant settings for this connection:- match identity remote key-id - Refers to the IKE identity used by the client. This string value is configured within the AnyConnect XML profile.
- identity local dn - Defines the IKE identity used by the FlexVPN hub. This value uses the value from within the certificate used.
- authentication remote - States that EAP should be used for client authentication.
- authentication local - States that certificates should be used for local authenticate.
- aaa authentication eap - States to use aaa authentication login list FlexVPN-AuthC-List-1 when EAP is used for authentiation.
- aaa authorization group eap list - States to use aaa authorization network list FlexVPN-AuthZ-List-1 with username of FlexVPN-Local-Policy-1 for authorization attributes.
- virtual-template 10 - Defines which template to use when a virtual-access interface is cloned.
- Configure an IPsec profile that links back to the IKEv2 profile defined in step 4.
Note: Cisco IOS utilizes Smart Defaults. As a result, a transform set does not need to be explicitly defined. Macbook air 2018 best buy.
- Configure the virtual template from which the virtual-access interfaces are cloned:
- ip unnumbered - Unnumber the interface from an Inside interface so IPv4 routing can be enabled on the interface.
- tunnel mode ipsec ipv4 - Defines the interface to be a VTI type tunnel.
- Limit the negotiation to SHA-1. (Optional)
Due to defect CSCud96246 (registered customers only) , the AnyConnect client might fail to correctly validate the FlexVPN Hub certificate. This issue is due to IKEv2 negotiating a SHA-2 function for Pseudo-Random Function (PRF) whereas the FlexVPN-Hub certificate has been signed using SHA-1. The configuration below limits the negotiation to SHA-1:
Microsoft Active Directory Server Configuration
- In Windows Server Manager, expand Roles > Network Policy and Access Server > NMPS (Local) > RADIUS Clients and Servers, and click RADIUS Clients.
The New RADIUS Client dialog box appears. - In the New RADIUS Client dialog box, add the Cisco IOS router as a RADIUS client:
- Click the Enable this RADIUS client check box.
- Enter a name in the Friendly name field. This example uses FlexVPN-Hub.
- Enter the IP address of the router in the Address field.
- In the Shared Secret area, click the Manual radio button, and enter the shared secret in the Shared secret and Confirm shared secret fields.
Note: The shared secret must match the shared secret configured on the router.
- Click OK.
- In the Server Manager interface, expand Policies, and choose Network Policies.
The New Network Policy dialog box appears. - In the New Network Policy dialog box, add a new network policy:
- Enter a name in the Policy name field. This example uses FlexVPN.
- Click the Type of network access server radio button, and choose Unspecified from the drop-down list.
- Click Next.
- In the New Network Policy dialog box, click Add to add a new condition.
- In the Select condition dialog box, select the NAS IPv4 Address condition, and click Add.
The NAS IPv4 Address dialog box appears. - In the NAS IPv4 Address dialog box, enter the IPv4 address of the network access server in order to limit the network policy to only requests that originate from this Cisco IOS router.
- Click OK.
- In the new Network Policy dialog box, click the Access granted radio button in order to allow the client access to the network (if the credentials provided by the user are valid), and click Next.
- Ensure only Microsoft: Secure password (EAP-MSCHAP v2) appears in the EAP Types area in order to allow EAP-MSCHAPv2 to be used as the communication method between the Cisco IOS device and Active Directory, and click Next.
Note: Leave all of the 'Less secure authentication methods' options unchecked.
- Continue through the wizard and apply any additional constraints or settings as defined by your organizations security policy. In addition, ensure that the policy is listed first in the processing order as shown in this image:
Client Configuration
- Create an XML profile within a text editor, and name it flexvpn.xml.
This example uses this XML profile:- is a text string that appears in the client.
- is the fully qualified domain name (FQDN) of the FlexVPN hub.
- configures the connection to use IKEv2/IPsec rather than SSL (the default in AnyConnect).
- configures the connection to use MSCHAPv2 within EAP. This value is required for authentication against Microsoft Active Directory.
- defines the string value that matches the client to a specific IKEv2 profile on the hub (see step 4 above).
Note: The client profile is something that is only used by the client. It is recommended that an administrator uses the Anyconnect Profile editor in order to create the client profile.
- Save the flexvpn.xml file to the appropriate directory as listed in this table:
OS Location Windows XP %ALLUSERSPROFILE%Application DataCiscoCisco AnyConnect Secure Mobility ClientProfile Windows Vista/7 %PROGRAMDATA%CiscoCisco AnyConnect Secure Mobility ClientProfile Mac OS X /opt/cisco/anyconnect/profile/ Linux /opt/cisco/anyconnect/profile/ - Close and restart the AnyConnect client.
- In the Cisco AnyConnect Secure Mobility Client dialog box, choose FlexVPN Hub, and click Connect.
The Cisco AnyConnect | FlexVPN Hub dialog box appears. - Enter a username and password, and click OK.
Verify
Flexvpn Anyconnect Windows
In order to verify the connection, use the show crypto session detail remote client-ipaddress command. Refer to show crypto session for more information about this command.
Anyconnect Flexvpn Over Ipv4+ipv6
Note: The Output Interpreter Tool (registered customers only) (OIT) supports certain show commands. Use the OIT to view an analysis of show command output.
Troubleshoot
In order to troubleshoot the connection, collect and analyze DART logs from the client and use these debug commands on the router: debug crypto ikev2 packet and debug crypto ikev2 internal.
Flexvpn Anyconnect Free
Note: Refer to Important Information on Debug Commands before you use debug commands.